You canunplug and plug back in the wireless router to reset it.ģ. Cycle the power to both of these devices.You can use a paper clip to reset the Protocol Adapter by pressing the recessed reset button.
These two devices should be located near one another. Screenshot of Pentair ScreenLogic2 Connect. connection cable, connect one end of the cable to the Protocol Sdapter and the other end to the Indoor Wireless Transceiver. Wireless Gotchas Wireless remotes and screenlogic wireless links add another dimension to troubleshooting communication problems - as mentioned above the problem can be the RS-485 connection to the various wireless components OR the wireless radio itself. Verify the wireless router Power LEDin on. Connect the ScreenLogic Interface indoor wireless transceiver to the ScreenLogic Interface Protocol adapter as follow: 1. Locate your ScreenLogic2 Protocol Adapter and wireless router. If step 1 does not fix this issue, go to step 2.Ģ. The Tablet reboot process will take approximately 20 seconds.ī. Wireless Tablet – Press the Suspend button located on the left-side of the Tablet for approximately 4seconds. In most cases, theeasiest way to re-establish a connection is to perform a cold boot of the ScreenLogic2 device:Ī. Make sure your wireless ScreenLogic2 device is connected to your wireless router. If ScreenLogic2has been previously working without a problem, try the following steps to resolve the problem:ġ. If the Configuration program displays “Looking for controller,” for longer then 60 seconds when you startIntelliTouch ScreenLogic2, this may indicate a communication problem somewhere in the system. Why does the Configuration program say “Looking for Controller”? 1.1 (which will then break all your other network devices connections) however then once the ScreenLogic was connected you could then change the gateway address in ScreenLogic settings back to use the homes gateway of 192.168.0.1. 0.1 so the fix was to go into the home router settings and change it to use 192.186. Here is a link that might be useful: Pentair Remote Control & Monitor user. With the ScreenLogic Interface and Wireless Connection Kit you can leave the house for work or vacation with the piece of mind that your pool system, no matter the case, will be in your control.There was a similar post about the ScreenLogic not being able to connect through the OPs home network, and it was due to the ScreenLogic having a default gateway (network address) setting of 192.168.1.1 For some reason the ScreenLogic reset itself to its default settings. Its a new interface for their IntelliTouch ScreenLogic pool control system. Click the Configure ScreenLogic button if you want to configure your system via the Configurator utility (see page 17 for more information).
For complete control, pool owners can operate, both, Intellibrite LED pool, spa and landscape lighting plus MagicStream Laminars. Click the Start ScreenLogic button to connect to your system and start the ScreenLogic2 Interface. Protocol adapter: Connects to wireless router via Ethernet connection and to Personality board (Load/Power. Not only does the Pentair ScreenLogic2 Application allow control of your pool and spa system, but your pool and spa lights as well. This allows pool owners to easily monitor and adjust to obtain healthy water and a safe pool environment. Pentair ScreenLogic 2 Interface also makes it possible to track and monitor your pH and ORP Level history with the use of the IntelliChem Chemical Control System with IntelliTouch or EasyTouch Automation. Or having Alexa™ activate your spa or waterįeature circuits or tell you the status of your pool with a simple voiceĬommand form your Amazon Echo™ device. With those you can also monitor and control your pool and spa from an Apple Systems, through controllers such as an iPad®, iPhone®, iPod touch® mobile The system hardware includes a Protocol adapter, a wireless router, and your choice of wired or wireless interface. The ScreenLogic2 Interface allows you to control the keyįunctions of a pool or spa using the IntelliTouch® and EasyTouch® control Your IntelliTouch ScreenLogic PDA, wireless Tablet, and in-wall touch screen are pre-configured and ready for operation.